This DIY can improves the signal of cell phone signal inside your house from 1 bar to full. Tape the section of the wire by the antenna hole down and then put the back of the phone back on.

Ultra Cheap Cell Phone Antenna Instructables

Mounting the exterior antenna for a homemade cell phone signal booster is simple.

Homemade cell phone antenna. Of course youd have to know which GSM frequency your phone is using at the time and need different size antennae for each frequency. Then about 19 millimeters away from one of the ends bend the paper clip at a 90-degree angle. A DIY cell phone signal booster can help you improve your access to cellular service in a variety of remote or rural areasYou can create your own wireless signal booster using a variety of standard home materials including a wire hanging and coaxial cable.

The one thing that is crucial to have is a metal coat hanger. You make a dipol antenna at 12 or 14 wavelength out of foil -- better would be copper tho. You can also use any slim metal tube such as a pen casing or metal drinking straw to form an external antenna.

Put this end into the antenna hole and bend the wire outside so it lays against the phone. Youll need to mount the amplifier near an outlet and out of the weather so its best to mount it inside the house in a spot where you can run cables to both antennas. It just clamps onto a typical antenna mast and the low-loss cable screws directly into it.

Using the ruler cut the wire so that it is about 13 inches 33 centimeters past the length of the phone. The Yagi-Uda antenna--often just called a Yagi--is a popular antenna due to its gain directionality and relatively lightweight design see the figure to the right. With the advent of phones with bluetooth wifi gps etc the antenna technology has had to change to allow these multiple radio signals to properly sendreceive.

The video will show u how to make a cell phone antenna booster with low cost items. Strip about 23 inches 5176 cm of the insulation off of the ethernet cord so the wires are exposed underneath. The MS-147 phone socket switches to disable the internal antenna when the MS-147 plug is inserted.

The result is likely that the vast majority of phone antennas that have been built support these multiple frequencies. Clip the end with a metal spring clamp. DIY 2G3G4G wireless cell phone signal booster is a home-brew booster which uses common household items.

Step 2 Connect one end of the coaxial cable to the outdoor antenna. Create an FM radio antenna by stripping the end from an ethernet cord. Next switch your phone to airplane mode which will disable WiFi and block any cell signals.

Just read the cell phone antenna booster sticker reviews and youll see what a scam these things are. This process is not overly difficult. Unlike the compact internal antenna on a USB modem or cell phone a Yagis driven element is large enough to be fully sensitive to the frequencies of interest.

Use a pair of scissors to cut off one end of an ethernet cord. After that bent wire inwards at 90 degrees. Home Latest Popular Trending Categories.

Ritter on Sep 15 2018 This sticker reminds me of people who want to make a homemade cell phone signal booster. Then measure 9 cm on both sides of the center. Make sure to have the antenna in the best location outside your home for the strongest signal.

Twist the wires together by hand as tightly as you can so they come to a point at the end. Plug your cell phone into the USB charger and wrap the cord around the metal tube. It is unlikely to switch.

DIY Cell Phone Antenna in 3 Minutes. On the left hand side of the webpage click cell phone amplifiers and choose the type of amplifier you need based on your cell phone providers frequency levels. Attach the other end to the amplifier.

You need to build 2 unit one indoor one outdoor both unit is similar and simple to build if you follow this guide but i take few hours to RD. At first to make the antenna you have to straighten wires with pliers and then you have to bent it accurately in the center at accurate 90 degrees. For 400 to 800 you can install your own homemade cell phone signal booster that boosts cell phone signals for flawless service.

Generally the external antenna socket is used to simply replace the existing modem antenna. Next take the ink cartridge out of a ballpoint pen and cut off 12-18 millimeters of the tubing that contains ink. However any small iron wire will also work.

Place your phone on a flat surface and sit a bottle of water above its top. Tape one end near the top of your cell phone so that the tube extends upward from the phone. MS-147 Used on ZTE Samsung and Telstra blue tick phones with an external antenna port.

To make a WiFi antenna using a paper clip start by straightening out the paper clip and cutting it so its 61 millimeters long. Art Animation Comedy Cool Commercials Cooking Entertainment How To Music Dance News Events People Stories Pets Animals Science Tech Sports Travel Outdoors Video Games Wheels Wings Other 18 Only Fashion.